Dynamic Route Map Display (DRMD) On-board Bus PIS High-end Infotainment Display for space constrained installations
28" Ultra-Wide active matrix color TFT with LED-backlight Resolution 1920 x 357 Brightness 1000nits, contrast 1000:1 Software controlled brightness and display parameters 6-core 64-bit RK3399 Multimedia SoC with dedicated firmware 16GB eMMC Flash for OS and application, SD-card slot Internal control fucntions: Temperature monitoring and control +50°C Controlled display start, power control LED backlight brightness control Event and error logging Supports Smart Graphics, bitmaps, animations, live video Internal 802.11n/ac WiFi 10/100/1000Mbit Ethernet Optional 3G /LTE modem with uSIM socket Optional High accuracy GNSS receiver Panel Surface Anti-glare, hard coating (3H) IP52, operating temperature -25 to 55°C
Tomi Hanninen SYSTEM 6-core 64-bit 2GHz RK-3399 SOC processor 2GB soldered down DRAM 8/16/32GB soldered down eMMC FLASH disk, SD card Internal SATA III controller 4x or 8x Composite video PAL camera inputs GBIT Ethernet interface 32-bit System management controller Secure electronic serial number Contactless tamper detection 3D accelerometer for rash driving detection SYSTEM MANAGEMENT CONTROLLER 32-bit CORTEX M3 controller Fallback for AIS140 mode system operation/li> Monitor tempertures, input, battery and system voltages System health monitor, safe and secure booting Failsafe mode operation, error recovery DISPLAY Serialized automotive display interface 1GHz, self clocked spread spectrum serialization 18-bit native LVDS interface, I2C-bus for touchscreen and 12V power HMI Display interface in single 4-pair CAT6 cable Compatible with DURION SCU driver console WIRELESS INTERFACES 5-band GPRS/3G/LTE CAT4 modem with APAC band support eSIM and uSIM support with SW configuration Full voice call support 802.11 a/b/g/n/ac high speed WiFi GNSS receiver with GPS/IRNSS/GLONASS support GPS and IRNSS meet AIS140 and UBS II performance criteria Optional Bluetooth 4.0 I/O INTERFACES 2x RS-232 ports, 1x RS-485 port, 1x external USB 2.0 2x CAN ports, one with full J1939 protocol support, second general purpose CAN2.0 4x Digital Inputs and 4x Digital outputs with 12/24VDc range 2x Analogue inputs , 5VDc and 10Vdc ranges 2x 10W Stereo outputs for PIS speakers 1x MIC input for driver Ignition input, Alarm output (Open collector), Error Output POWER SUPPLY 8-38VDC input range power supply Load dump protection to 130VDc, 48VDC reverse voltage protection +-2KV surge and burst protection Inbuilt LiPO battery with integrated charge and power management Automatic fallback on AIS140 mode during power interruption 4-hour autonomy with GNSS and modem support Input voltage, power rail, battery voltage monitoring CONNECTORS 2X 35-pin keyed AMPSEAL connectors X-coded M12 connector for digital display TNC connectors for cellular and GNSS MECHANICAL Die-cast aluminum enclosure Weight (TBD) Dimensions (TBD) ENVIRONMENTAL -25 ~ +80°C operating temperature 95% RH, non condensing IP65 ingress protection
SYSTEM 4-core 64-bit ARM Application Processor 512KB DRAM, 2GB eMMC Flash disk SD-slot for storage expansion CORTEX M0 System Management Controller Electronic serial number and temperature sensor Internal power supply voltage monitoring OS AND SW OPTIONS: WRT Linux for router-type applications YOCTO-Linux Software for accelerometer interfacing AIS140 protocol support STANDARD INTERFACES: 10/100Mbit Ethernet port 1x J1939 FMS CAN, 1x CAN 2.0 1x RS-485 1-wire interface Ignition Key and Emergency inputs (0-30VDC) Wheel-tick and direction sensing inputs (0-30VDC) 2x MOSFET Open Drain Outputs OPTIONAL INTERFACES: DUAGON MVB Dual redundant EMD interfaces 2x DB-9 connectors MECHANICALWIRELESS INTERFACES: SIM7600 CAT 1 LTE modem with eSIM and uSIM slot Modem band specification available upon request DR assisted GNSS receiver (ADR and UDR supported) MECHANICAL: Anodized Aluminum extruded enclosure (Blue) uSIM under rear panel RJ45 FAKRA C-D Code, I/O connector, (2x DB9) POWER SUPPLY: 8-36VDC Active voltage clamp, compliant with ISO 7637-2 and EN50155 5W typical power consumption DIMENSIONS: 104mm(W) x 104mm(D) x 3mm(H) Flanges 10mm WEIGHT: 0.3Kg TEMPERATURE RANGE: Operating: -25° to +55°C Storage: -40° to +85°C HUMIDITY: 95% at 45°C non-condensing PROTECTION: IP41
SYSTEM 6-core 64-bit 2GHz Linux ARM SOC processor 32-bit CORTEX M0 system management coprocessor 2GB soldered down DRAM 8GB soldered down eMMC FLASH disk, SD-card Internal Dual NVME SSD M.2 <-key sockets Secure electronic serial number and TPM 2.0 DISPLAY INTERFACES ChannelLink III Serialized automotive display interface Self-clocked spread spectrum serialization of LVDS and I2C 18-bit native LVDS, I2C-bus for touchscreen, 12V power HMI Display interface in single pair of CAT5 cable Compatible with DURION SCU PCAP HMI WIRELESS INTERFACES 5-band LTE CAT4 modem with APAC band support uSIM slot (under service panel) Support for soldered down eSIM (software selectable) 802.11ax/ac high speed WiFi UDR supported L1/L5 GNSS receiver with GPS/IRNSS/GLONASS support SENSORS Internal temperature 3D accelerometer 3D gyroscope I/O INTERFACES 1x RS-232 ports, 1x RS-485 port, 1x external USB 2.0 1x 10/100/1000Mbit Ethernet Stereo output LINE-levels Stereo input LINE-levels (ambient noise level sensing) 1x MIC input for announcements SERVICE INTERFACES (under service panel) 1x USB 2.0 1x service HDMI Audio Jack, MIC In, Headset outputs Reset Button POWER SUPPLY 9-38VDC input range power supply Supercapacitor Back-up for 2min (option) 48VDC reverse voltage protection +-2KV surge and burst protection +12VDC regulated power output (25W) CONNECTORS 23-pin keyed AMPSEAL connectors X-coded M12 connector for Ethernet A-coded M12 connector for HMI SMA connectors for cellular, WiFi and GNSS MECHANICAL Die-cast aluminum enclosure Weight (TBD) Dimensions (TBD) ENVIRONMENTAL -25 ~ +55°C operating temperature 95% RH, non condensing IP65 ingress protection